5G100m wireless HDMI extender WE100 connection using video tutorial

2019-08-07 14:37:40 ekL

5G100m wireless HDMI extender WE100 connection using video tutorial

Introduction to Wireless HDMI Extender WE100

        The wireless HDMI extender WE100 can transmit the HDMI signal farthest to 100 meters through the 5G signal in an open environment; the wireless HDMI extender WE100 supports one transmitter and one to four receivers simultaneously connected, and The transmitter supports one HDMI signal output, which is very convenient for connecting multiple HDMI devices.

Wireless HDMI Extender WE100

Wireless HDMI Extender WE100

Wireless HDMI Extender WE100 Features

        ①The transmitter provides an HDMI local loop

        ②Support for 5.1 channel digital audio

        ③Support 1920*1080p@60Hz HD resolution

        ④Support infrared extension, can control the source device at the remote end

        ⑤Compatible with HDMI 1.3, HDCP 1.4

        ⑥No need to install software, plug and play

        ⑦Support one transmitter and one to four receivers simultaneously

        ⑧Support 5G signal wireless extension 100 meters (empty environment)

        Note: The wireless transmission distance depends on the environment. Solid objects such as reinforced concrete and bricks may affect the actual transmission effect and shorten the transmission distance. The human body may also block the signal transmission. Please take the actual transmission distance as the standard!

Wireless HDMI Extender WE100 Interface Description

Wireless HDMI Extender WE100 Interface Description

Wireless HDMI Extender WE100 Interface Description

        ①Ground connector: ground connection

        ②DC IN: power interface

        ③POWER : Power indicator

        ④STATUS: indicator light transmission

        ⑤LINK: Paired connection success indicator

        ⑥RESET: Reset / Pair button

        ⑦HDMI OUT: HDMI signal output

        ⑧HDMI IN: HDMI signal input

        ⑨IR Ext: Infrared extension cable interface

        ⑩HDMI OUT: HDMI signal output

Wireless HDMI Extender WE100 Connection Diagram

Wireless HDMI Extender WE100 Connection Diagram

Wireless HDMI Extender WE100 Connection Diagram

Wireless HDMI Extender WE100 Installation Step Guide

        01. Connect the transmitter to the signal source with a high-quality HDMI cable, and the receiver to the TV.

        02. Connect the infrared extension cable to the transmitting/receiving end and operate with the remote control.

        03, connect the power supply

        04. Ensure that there is no solid object blocking at the transmitting end and the receiving end. The wireless transmission distance depends on the environment. Solid objects such as reinforced concrete and bricks may affect the actual transmission effect and shorten the transmission distance. The human body may also block signal transmission.

Wireless HDMI Extender WE100 Wireless Pairing Instructions

        Wireless HDMI Extender One-to-One Pair Code (default is already paired)

        Note: The default factory equipment has been paired by default, and supports any one transmitter to pair with any receiver.

        01. Take one transmitter (TX) host and one receiver (RX) host to check whether it works normally.

        02. Use the HDMI cable to connect to the HDMI IN port on the TX side, and the other end to the HDMI OUT port on the RX side or connect the ground cable to each other.

        03. Power on both the TX and RX terminals and wait for the system to start, about 30 seconds.

        04. After the system is started, when the three indicators on the two terminals of the TX and RX terminals are flashing normally, first press the reset button on the RX terminal, then press the reset button on the TX terminal and wait for the RX. Pairing with the TX end

        05. Wait about 30-60 seconds to see if the STATUS indicator on the TX and RX terminals are flashing at the same time. If it is flashing at the same time, the pairing is successful, such as the STATUS indication on the TX and RX terminals after waiting for more than 60 seconds. The light has not flashed at the same time, repeat step 4

        06. Press and hold the reset button to restore the factory settings to unpair and return to the default state.


        Wireless HDMI Extender One-to-Many Pair Code

        Note: By default, any one transmitter (only one transmitter can be powered) can be paired with 1-4 receivers, no need to pair separately; when multiple transmitters work at the same time, please match the following operations

        01. Take two transmitter (TX) hosts and 1-4 receivers (RX) to power on and check whether they can work normally.

        02. Connect all the screws at the grounding wire position on the outer casing of the main unit with one wire to ensure that the paired transmitting end (TX) and receiving end (RX) main ground are connected together.

        03. Then power on, after the system starts, press and hold the RESET button on the transmitter (TX) until the LINK indicator is off, then press the RESET button on the receiving end (RX) until the LINK indicator is off, wait 30 seconds. Left and right, you can pair successfully (Note: After the pairing is successful, the paired receiver only receives the transmitter signal paired with it)

        04. If it is unsuccessful, please press the RESET button of the transmitter (TX) and receiver (RX) until all the lights are off and the system restarts. After the system restarts, follow step 03.

VIP Service Hotline 13530061759 service hours:
09:00-12:00 AM
13:30-18:30 PM
Service Hotline
0755-29806840 ext 106

Amazon
E-mail
Map
Alibaba